summaryrefslogtreecommitdiff
path: root/trunk/users/metalab/GCode_Interpreter_SD/_init.h.shotbot
blob: 8b61263b4cfd512f8b7628ebebe0de60f1cd31f0 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
// Yep, this is actually -*- c++ -*-
#ifndef INIT_H_
#define INIT_H_

// Prints debug output on the serial port - makes stuff slower
#define DEBUG 1


// define the parameters of our machine.
#define X_STEPS_PER_INCH 5080
#define X_STEPS_PER_MM   200
#define X_MOTOR_STEPS    200

#define Y_STEPS_PER_INCH 5080
#define Y_STEPS_PER_MM   200
#define Y_MOTOR_STEPS    200

#define Z_STEPS_PER_INCH 5080
#define Z_STEPS_PER_MM   200
#define Z_MOTOR_STEPS    200

//our maximum feedrates
#define FAST_XY_FEEDRATE 1000.0
#define FAST_Z_FEEDRATE  50.0

// Units in curve section
#define CURVE_SECTION_INCHES 0.019685
#define CURVE_SECTION_MM 0.5

// Set to one if endstop outputs are inverting (ie: 1 means open, 0 means closed)
// RepRap opto endstops are *not* inverting.
#define ENDSTOPS_INVERTING 0
// Optionally disable max endstops to save pins or wiring
#define ENDSTOP_X_MIN_ENABLED 1
#define ENDSTOP_X_MAX_ENABLED 0
#define ENDSTOP_Y_MIN_ENABLED 1
#define ENDSTOP_Y_MAX_ENABLED 0
#define ENDSTOP_Z_MIN_ENABLED 1
#define ENDSTOP_Z_MAX_ENABLED 0

// How many temperature samples to take.  each sample takes about 100 usecs.
#define TEMPERATURE_SAMPLES 5

// The *_ENABLE_PIN signals are active high as default. Define this
// to one if they should be active low instead (e.g. if you're using different
// stepper boards).
// RepRap stepper boards are *not* inverting.
#define INVERT_ENABLE_PINS 1

// If you use this firmware on a cartesian platform where the
// stepper direction pins are inverted, set these defines to 1
// for the axes which should be inverted.
// RepRap stepper boards are *not* inverting.
#define INVERT_X_DIR 0
#define INVERT_Y_DIR 0
#define INVERT_Z_DIR 0

// Defines in which logical direction to move when using the G30 command
// (home to physical reference switches). 1 is positive, 0 is negative
#define REFERENCE_X_DIR 0
#define REFERENCE_Y_DIR 0
#define REFERENCE_Z_DIR 0

/****************************************************************************************
* digital i/o pin assignment
*  
* this uses the undocumented feature of Arduino - pins 14-19 correspond to analog 0-5
****************************************************************************************/

//cartesian bot pins
#define X_STEP_PIN 2
#define X_DIR_PIN 3
#define X_MIN_PIN 4
#define X_MAX_PIN 9
#define X_ENABLE_PIN 15

#define Y_STEP_PIN 10
#define Y_DIR_PIN 7
#define Y_MIN_PIN 8
#define Y_MAX_PIN 13
#define Y_ENABLE_PIN 15

#define Z_STEP_PIN 19
#define Z_DIR_PIN 18
#define Z_MIN_PIN 16
#define Z_MAX_PIN 17
#define Z_ENABLE_PIN 15

//extruder pins
#define EXTRUDER_MOTOR_SPEED_PIN   11
#define EXTRUDER_MOTOR_DIR_PIN     12
#define EXTRUDER_HEATER_PIN        6
#define EXTRUDER_FAN_PIN           5
#define EXTRUDER_THERMISTOR_PIN    0  //NB! analog pin, -1 disables thermistor readings
#define EXTRUDER_THERMOCOUPLE_PIN  -1 //NB! analog pin, -1 disables thermocouple readings

// Enable/disable features
#define ENABLE_ARCS                0

enum Axis {
  X_AXIS = 0,  
  Y_AXIS = 1,
  Z_AXIS = 2
};

struct AxisConfig {
  uint8_t step_pin;
  uint8_t dir_pin;
  uint8_t min_pin;
  uint8_t max_pin;
  uint8_t enable_pin;
  bool invert_dir;
  bool reference_dir;
  bool min_endstop_enabled;
  bool max_endstop_enabled;

  uint16_t steps_per_inch;
  uint16_t steps_per_mm;
  uint16_t motor_steps;
};

extern AxisConfig axes[3];

#endif // INIT_H_