blob: 978df1e98d2b174f66ef5914a42b27389f639734 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
|
# HAL config file for Vital Systems MOTENC-100 PCI board
#
# Install driver.
#loadrt hal_motenc
# Classicladder for machine logic (load the realtime portion).
# Just uncomment the following line if you want a Software PLC
#loadrt classicladder_rt numRungs=4 numBits=16 numWords=4 numTimers=2 numMonostables=2 numPhysInputs=16 numPhysOutputs=8 numArithmExpr=4 numSections=1
# Invoke the user part of CL to silently load the program.
# Just uncomment the following line if you want a Software PLC
#loadusr -w classicladder --nogui ../configs/common/bridgeport.clp
# Add I/O to servo thread so they will be evaluated
# every servo period.
# inputs get read at the beginning of the thread
addf motenc.0.misc-update servo-thread 1
#addf motenc.0.adc-read servo-thread 1
addf motenc.0.digital-in-read servo-thread 1
#addf classicladder.0.refresh servo-thread 1
# outputs get refreshed at the end of the thread
addf motenc.0.digital-out-write servo-thread -1
#
# Connect motion controller I/Os
#
# Connect limit/home switch outputs to motion controller.
net Xminlim <= motenc.0.in-00
net Xminlim => axis.0.neg-lim-sw-in
net Xmaxlim <= motenc.0.in-01
net Xmaxlim => axis.0.pos-lim-sw-in
net Xhome <= motenc.0.in-02
net Xhome => axis.0.home-sw-in
net Yminlim <= motenc.0.in-04
net Yminlim => axis.1.neg-lim-sw-in
net Ymaxlim <= motenc.0.in-05
net Ymaxlim => axis.1.pos-lim-sw-in
net Yhome <= motenc.0.in-06
net Yhome => axis.1.home-sw-in
net Zminlim <= motenc.0.in-08
net Zminlim => axis.2.neg-lim-sw-in
net Zmaxlim <= motenc.0.in-09
net Zmaxlim => axis.2.pos-lim-sw-in
net Zhome <= motenc.0.in-10
net Zhome => axis.2.home-sw-in
# Connect amp faults to motion controller.
net Xfault <= motenc.0.in-03
net Xfault => axis.0.amp-fault-in
net Yfault <= motenc.0.in-07
net Yfault => axis.1.amp-fault-in
net Zfault <= motenc.0.in-11
net Zfault => axis.2.amp-fault-in
# Connect amp enables to motion controller.
net Xenable => motenc.0.out-08
net Yenable => motenc.0.out-09
net Zenable => motenc.0.out-10
# Connect watchdog reset to mot ion controller.
#newsig WatchdogRst bit
#linksp WatchdogRst <= motenc.watchdog-reset
#linksp WatchdogRst => motion.watchdog-reset-out
#
# Connect I/O controller I/Os
#
# Connect e-stop write/sense to I/O controller.
#
# The estop from the opto module should be jumpered to one of the
# motenc estop pins. This will notify the moten of the estop condition
# and it will zero the DACs and turn off all output even if the PC
# has crashed.
#
net EstopSense <= motenc.0.estop-in-not
#linksp EstopSense <= motenc.0.in-15
net EstopSense => iocontrol.0.emc-enable-in
net EstopWrite => motenc.0.out-07
net EstopWrite <= iocontrol.0.user-enable-out
# ESTOP loopback, only use this for a simple machine without external ESTOP
# you really SHOULDN'T use a servo machine without proper ESTOP
#net estop-loop iocontrol.0.user-enable-out iocontrol.0.emc-enable-in
# Connect spindle fwd/rev to I/O controller.
net SpindleFwd => motenc.0.out-00
net SpindleFwd <= motion.spindle-forward
net SpindleRev => motenc.0.out-01
net SpindleRev <= motion.spindle-reverse
# Connect spindle brake to I/O controller.
net SpindleBrakeOn => motenc.0.out-02
net SpindleBrakeOn <= motion.spindle-brake
# Connect mist/flood coolant to I/O controller.
net MistOn => motenc.0.out-05
net MistOn <= iocontrol.0.coolant-mist
net FloodOn => motenc.0.out-06
net FloodOn <= iocontrol.0.coolant-flood
# Connect lube motor run to I/O controller.
net LubeOn => motenc.0.out-12
net LubeOn <= iocontrol.0.lube
# Connect lube level to I/O controller.
net LubeLevel <= motenc.0.in-14
net LubeLevel => iocontrol.0.lube_level
|
