summaryrefslogtreecommitdiff
path: root/trunk/darwin/firmware/Sanguino/Sanguino3G/gcode/MasterGCodeInterpreter/MasterGCodeInterpreter.pde
blob: 9d337163d9b6ce4bfe64e7660d2a51d1b1842f2d (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
// Yep, this is actually -*- c++ -*-

// Arduino G-code Interpreter
// v1.0 by Mike Ellery - initial software (mellery@gmail.com)
// v1.1 by Zach Hoeken - cleaned up and did lots of tweaks (hoeken@gmail.com)
// v1.2 by Chris Meighan - cleanup / G2&G3 support (cmeighan@gmail.com)
// v1.3 by Zach Hoeken - added thermocouple support and multi-sample temp readings. (hoeken@gmail.com)
#include <WProgram.h>
#include <SimplePacket.h>
#include "Commands.h"
#include "Configuration.h"
#include "RS485.h"
#include "Variables.h"

//our command string
#define COMMAND_SIZE 128
char word[COMMAND_SIZE];
byte serial_count;
int no_data = 0;
long idle_time;
boolean comment = false;
boolean bytes_received = false;

void setup()
{
	pinMode(RX_ENABLE_PIN, OUTPUT);
  pinMode(TX_ENABLE_PIN, OUTPUT);
  digitalWrite(RX_ENABLE_PIN, LOW); //always listen.

  Serial.begin(HOST_SERIAL_SPEED);
  Serial1.begin(SLAVE_SERIAL_SPEED);

	Serial.println("start");
	
	//other initialization.
	init_process_string();
	init_steppers();
	init_tool(0);
}

void loop()
{
	char c;

	//read in characters if we got them.
	if (Serial.available() > 0)
	{
		c = Serial.read();
		no_data = 0;

		//newlines are ends of commands.
		if (c != '\n')
		{
			// Start of comment - ignore any bytes received from now on
			if (c == '(')
				comment = true;
				
			// If we're not in comment mode, add it to our array.
			if (!comment)
			{
				word[serial_count] = c;
				serial_count++;
			}
			if (c == ')')
			        comment = false; // End of comment - start listening again
		}

		bytes_received = true;
	}
	//mark no data if nothing heard for 100 milliseconds
	else
	{
		if ((millis() - idle_time) >= 100)
		{
			no_data++;
			idle_time = millis();
		}
	}

	//if theres a pause or we got a real command, do it
	if (bytes_received && (c == '\n' || no_data ))
	{
		//process our command!
		process_string(word, serial_count);

		//clear command.
		init_process_string();
	}

	//no data?  turn off steppers
	if (no_data > 10 )
		disable_steppers();
}