path: root/trunk/users/bruce/GCode_Interpreter_SD/process_string.pde

/* -*- mode: c++; c-basic-offset: 8; indent-tabs-mode: t -*- */

// Our point structures to make things nice.
struct LongPoint
{
  long p[3];
};

struct FloatPoint
{
  float p[3];
};

// G-code line parse results
struct GcodeParser
{
  unsigned int seen;
  int G;
  int M;
  float P;
  float X;
  float Y;
  float Z;
  float I;
  float J;
  float F;
  float S;
  float R;
  float Q;
};

FloatPoint current_units;
FloatPoint target_units;
FloatPoint delta_units;

LongPoint current_steps;
LongPoint target_steps;
LongPoint delta_steps;

bool abs_mode = false; //0 = incremental; 1 = absolute

//default to mm for units
float units[3] = {X_STEPS_PER_MM, Y_STEPS_PER_MM, Z_STEPS_PER_MM};
#if ENABLE_ARCS == 1
float curve_section = CURVE_SECTION_MM;
#endif

//our direction vars
bool direction[3] = {true, true, true};

int scan_int(char *str, int *valp);
int scan_float(char *str, float *valp);

//our feedrate variables.
float feedrate = 0.0;
long feedrate_micros = 0;

/* keep track of the last G code - this is the command mode to use
 * if there is no command in the current string 
 */
int last_gcode_g = -1;

/* bit-flags for commands and parameters */
#define GCODE_G	(1<<0)
#define GCODE_M	(1<<1)
#define GCODE_P	(1<<2)
#define GCODE_X	(1<<3)
#define GCODE_Y	(1<<4)
#define GCODE_Z	(1<<5)
#define GCODE_I	(1<<6)
#define GCODE_J	(1<<7)
#define GCODE_K	(1<<8)
#define GCODE_F	(1<<9)
#define GCODE_S	(1<<10)
#define GCODE_Q	(1<<11)
#define GCODE_R	(1<<12)

#define TYPE_INT 1
#define TYPE_FLOAT 2

/* macros to save typing and bugs in the parser function */
#define PARSE_INT(ch, instr, str, str_size, len, val, seen, flag)       \
  case ch:                                                              \
  len = scan_int(str, &val, &seen, flag);                               \
  break;

#define PARSE_FLOAT(ch, instr, str, str_size, len, val, seen, flag)     \
  case ch:                                                              \
  len = scan_float(str, &val, &seen, flag);                             \
  break;

int parse_string(struct GcodeParser * gc, char instruction[], int size)
{
  int ind;
  int len;	/* length of parameter argument */

  gc->seen = 0;

  len=0;
  /* scan the string for commands and parameters, recording the arguments for each,
   * and setting the seen flag for each that is seen
   */
  for (ind=0; ind<size; ind += (1+len)) {
    len = 0;
    switch (instruction[ind]) {
      PARSE_INT('G', instruction, &instruction[ind+1], size-ind, len, gc->G, gc->seen, GCODE_G);
      PARSE_INT('M', instruction, &instruction[ind+1], size-ind, len, gc->M, gc->seen, GCODE_M);
      PARSE_FLOAT('S', instruction, &instruction[ind+1], size-ind, len, gc->S, gc->seen, GCODE_S);
      PARSE_FLOAT('P', instruction, &instruction[ind+1], size-ind, len, gc->P, gc->seen, GCODE_P);
      PARSE_FLOAT('X', instruction, &instruction[ind+1], size-ind, len, gc->X, gc->seen, GCODE_X);
      PARSE_FLOAT('Y', instruction, &instruction[ind+1], size-ind, len, gc->Y, gc->seen, GCODE_Y);
      PARSE_FLOAT('Z', instruction, &instruction[ind+1], size-ind, len, gc->Z, gc->seen, GCODE_Z);
      PARSE_FLOAT('I', instruction, &instruction[ind+1], size-ind, len, gc->I, gc->seen, GCODE_I);
      PARSE_FLOAT('J', instruction, &instruction[ind+1], size-ind, len, gc->J, gc->seen, GCODE_J);
      PARSE_FLOAT('F', instruction, &instruction[ind+1], size-ind, len, gc->F, gc->seen, GCODE_F);
      PARSE_FLOAT('R', instruction, &instruction[ind+1], size-ind, len, gc->R, gc->seen, GCODE_R);
      PARSE_FLOAT('Q', instruction, &instruction[ind+1], size-ind, len, gc->Q, gc->seen, GCODE_Q);
      break;
    }
  }
}


//Read the string and execute instructions
void process_string(char instruction[], int size)
{

  GcodeParser gc;	/* string parse result */

  //the character / means delete block... used for comments and stuff.
  if (instruction[0] == '/') {
    Serial.print("ok:");
    Serial.println(128-Serial.available(), DEC);
    return;
  }

  //init baby!
  FloatPoint fp;
  fp.p[X_AXIS] = 0.0;
  fp.p[Y_AXIS] = 0.0;
  fp.p[Z_AXIS] = 0.0;

  //get all our parameters!
  parse_string(&gc, instruction, size);

  // 	/* if no command was seen, but parameters were, then use the last G code as 
  // 	 * the current command
  // 	 */
  // 	if ((!(gc.seen & (GCODE_G | GCODE_M))) && 
  // 	    ((gc.seen != 0) &&
  // 		(last_gcode_g >= 0))
  // 	)
  // 	{
  // 		/* yes - so use the previous command with the new parameters */
  // 		gc.G = last_gcode_g;
  // 		gc.seen |= GCODE_G;
  // 	}

  //did we get a gcode?
  if (gc.seen & GCODE_G) {
    last_gcode_g = gc.G;	/* remember this for future instructions */
    fp = current_units;
    if (abs_mode) {
      if (gc.seen & GCODE_X)
        fp.p[X_AXIS] = gc.X;
      if (gc.seen & GCODE_Y)
        fp.p[Y_AXIS] = gc.Y;
      if (gc.seen & GCODE_Z)
        fp.p[Z_AXIS] = gc.Z;
    }
    else {
      if (gc.seen & GCODE_X)
        fp.p[X_AXIS] += gc.X;
      if (gc.seen & GCODE_Y)
        fp.p[Y_AXIS] += gc.Y;
      if (gc.seen & GCODE_Z)
        fp.p[Z_AXIS] += gc.Z;
    }

    // Get feedrate if supplied
    if ( gc.seen & GCODE_F )
      feedrate = gc.F;

    //do something!
    switch (gc.G) {
      //Rapid Positioning
      //Linear Interpolation
      //these are basically the same thing.
    case 0:
    case 1:
      //set our target.
      set_target(fp.p[X_AXIS], fp.p[Y_AXIS], fp.p[Z_AXIS]);

      // Use currently set feedrate if doing a G1
      if (gc.G == 1)
        feedrate_micros = calculate_feedrate_delay(feedrate);
      // Use our max for G0
      else
        feedrate_micros = getMaxSpeed();

//       Serial.println(feedrate, DEC);
//       Serial.println(feedrate_micros, DEC);

      //finally move.
      dda_move(feedrate_micros);
      break;
#if ENABLE_ARCS == 1
      //Clockwise arc
    case 2:
      //Counterclockwise arc
    case 3: {
      FloatPoint cent;

      // Centre coordinates are always relative
      if (gc.seen & GCODE_I) cent.p[X_AXIS] = current_units.p[X_AXIS] + gc.I;
      else cent.p[X_AXIS] = current_units.p[X_AXIS];
      if (gc.seen & GCODE_J) cent.p[Y_AXIS] = current_units.p[Y_AXIS] + gc.J;
      else cent.p[Y_AXIS] = current_units.p[Y_AXIS];

      float angleA, angleB, angle, radius, length, aX, aY, bX, bY;

      aX = (current_units.p[X_AXIS] - cent.p[X_AXIS]);
      aY = (current_units.p[Y_AXIS] - cent.p[Y_AXIS]);
      bX = (fp.p[X_AXIS] - cent.p[X_AXIS]);
      bY = (fp.p[Y_AXIS] - cent.p[Y_AXIS]);

      // Clockwise
      if (gc.G == 2) {
        angleA = atan2(bY, bX);
        angleB = atan2(aY, aX);
      }
      // Counterclockwise
      else {
        angleA = atan2(aY, aX);
        angleB = atan2(bY, bX);
      }

      // Make sure angleB is always greater than angleA
      // and if not add 2PI so that it is (this also takes
      // care of the special case of angleA == angleB,
      // ie we want a complete circle)
      if (angleB <= angleA)
        angleB += 2 * M_PI;
      angle = angleB - angleA;

      radius = sqrt(aX * aX + aY * aY);
      length = radius * angle;
      int steps, s, step;

      // Maximum of either 2.4 times the angle in radians or the length of the curve divided by the constant specified in _init.pde
      steps = (int) ceil(max(angle * 2.4, length / curve_section));

      FloatPoint newPoint;
      float arc_start_z = current_units.p[Z_AXIS];
      for (s = 1; s <= steps; s++) {
        step = (gc.G == 3) ? s : steps - s; // Work backwards for CW
        newPoint.p[X_AXIS] = cent.p[X_AXIS] + radius * cos(angleA + angle
                                                           * ((float) step / steps));
        newPoint.p[Y_AXIS] = cent.p[Y_AXIS] + radius * sin(angleA + angle
                                                           * ((float) step / steps));
        set_target(newPoint.p[X_AXIS], newPoint.p[Y_AXIS], arc_start_z + (fp.p[Z_AXIS]
                                                                          - arc_start_z) * s / steps);

        // Need to calculate rate for each section of curve
        if (feedrate > 0)
          feedrate_micros = calculate_feedrate_delay(feedrate);
        else
          feedrate_micros = getMaxSpeed();

        // Make step
        dda_move(feedrate_micros);
      }
    }
      break;
#endif // ENABLE_ARCS
			
    case 4: //Dwell
      delay((int)(gc.P * 1000));
      break;

      //Inches for Units
    case 20:
      units[X_AXIS] = X_STEPS_PER_INCH;
      units[Y_AXIS] = Y_STEPS_PER_INCH;
      units[Z_AXIS] = Z_STEPS_PER_INCH;
#if ENABLE_ARCS == 1
      curve_section = CURVE_SECTION_INCHES;
#endif

      calculate_deltas();
      break;

      //mm for Units
    case 21:
      units[X_AXIS] = X_STEPS_PER_MM;
      units[Y_AXIS] = Y_STEPS_PER_MM;
      units[Z_AXIS] = Z_STEPS_PER_MM;
#if ENABLE_ARCS == 1
      curve_section = CURVE_SECTION_MM;
#endif
      calculate_deltas();
      break;

      //go home.
    case 28:
      set_target(0.0, 0.0, 0.0);
      dda_move(getMaxSpeed());
      break;

      // Home to physical switches
    case 30:
      if (gc.seen & GCODE_Z) {
        home_axis(Z_AXIS);
        current_units.p[Z_AXIS] = 0.0;
      }
      if (gc.seen & GCODE_Y) {
        home_axis(Y_AXIS);
        current_units.p[Y_AXIS] = 0.0;
      }
      if (gc.seen & GCODE_X) {
        home_axis(X_AXIS);
        current_units.p[X_AXIS] = 0.0;
      }

      // Move to given offset (fp is overwritten by home_axis)
      if (gc.seen & GCODE_X) fp.p[X_AXIS] = gc.X;
      else fp.p[X_AXIS] = current_units.p[X_AXIS];
      if (gc.seen & GCODE_Y) fp.p[Y_AXIS] = gc.Y;
      else fp.p[Y_AXIS] = current_units.p[Y_AXIS];
      if (gc.seen & GCODE_Z) fp.p[Z_AXIS] = gc.Z;
      else fp.p[Z_AXIS] = current_units.p[Z_AXIS];

      set_target(fp.p[X_AXIS], fp.p[Y_AXIS], fp.p[Z_AXIS]);
      feedrate_micros = calculate_feedrate_delay(feedrate);
      dda_move(feedrate_micros);

      break;

      // Drilling canned cycles
    case 81: // Without dwell
    case 82: // With dwell
    case 83: { // Peck drilling
      float retract = gc.R;
				
      if (!abs_mode)
        retract += current_units.p[Z_AXIS];

      // Retract to R position if Z is currently below this
      if (current_units.p[Z_AXIS] < retract) {
        set_target(current_units.p[X_AXIS], current_units.p[Y_AXIS], retract);
        dda_move(getMaxSpeed());
      }

      // Move to start XY
      set_target(fp.p[X_AXIS], fp.p[Y_AXIS], current_units.p[Z_AXIS]);
      dda_move(getMaxSpeed());

      // Do the actual drilling
      float target_z = retract;
      float delta_z;

      // For G83 move in increments specified by Q code, otherwise do in one pass
      if (gc.G == 83)
        delta_z = gc.Q;
      else
        delta_z = retract - fp.p[Z_AXIS];

      do {
        // Move rapidly to bottom of hole drilled so far (target Z if starting hole)
        set_target(fp.p[X_AXIS], fp.p[Y_AXIS], target_z);
        dda_move(getMaxSpeed());

        // Move with controlled feed rate by delta z (or to bottom of hole if less)
        target_z -= delta_z;
        if (target_z < fp.p[Z_AXIS])
          target_z = fp.p[Z_AXIS];
        set_target(fp.p[X_AXIS], fp.p[Y_AXIS], target_z);
        if (feedrate > 0)
          feedrate_micros = calculate_feedrate_delay(feedrate);
        else
          feedrate_micros = getMaxSpeed();
        dda_move(feedrate_micros);

        // Dwell if doing a G82
        if (gc.G == 82)
          delay((int)(gc.P * 1000));

        // Retract
        set_target(fp.p[X_AXIS], fp.p[Y_AXIS], retract);
        dda_move(getMaxSpeed());
      } while (target_z > fp.p[Z_AXIS]);
    }
      break;

			
    case 90: //Absolute Positioning
      abs_mode = true;
      break;

			
    case 91: //Incremental Positioning
      abs_mode = false;
      break;

			
    case 92: //Set as home
      set_position(0.0, 0.0, 0.0);
      break;

      /*
      //Inverse Time Feed Mode
      case 93:

      break;  //TODO: add this

      //Feed per Minute Mode
      case 94:

      break;  //TODO: add this
      */

    default:
      Serial.print("Unsupported G-Code: G");
      Serial.println(gc.G, DEC);
    }
    Serial.print("ok:");
    Serial.println(128-Serial.available(), DEC);
    return;
  }

  //find us an m code.
  if (gc.seen & GCODE_M) {
    switch (gc.M) {
      //TODO: this is a bug because search_string returns 0.  gotta fix that.
    case 0:
      true;
      break;
      /*
        case 0:
        //todo: stop program
        break;

        case 1:
        //todo: optional stop
        break;

        case 2:
        //todo: program end
        break;
      */
      //turn extruder on, forward
    case 101:
      extruder_set_direction(true);
      extruder_set_speed(extruder_speed);
      break;

      //turn extruder on, reverse
    case 102:
      extruder_set_direction(false);
      extruder_set_speed(extruder_speed);
      break;

      //turn extruder off
    case 103:
      extruder_set_speed(0);
      break;

      //custom code for temperature control
    case 104:
      if (gc.seen & GCODE_S)
        {
          extruder_set_temperature((int)gc.S);

          //warmup if we're too cold.
          while (extruder_get_temperature() < extruder_target_celsius)
            {
              extruder_manage_temperature();
              Serial.print("T:");
              Serial.println(extruder_get_temperature());
              delay(1000);
            }
        }
      break;

      //custom code for temperature reading
    case 105:
      Serial.print("T:");
      Serial.println(extruder_get_temperature());
      break;

      //turn fan on
    case 106:
      extruder_set_cooler(255);
      break;

      //turn fan off
    case 107:
      extruder_set_cooler(0);
      break;

      //set max extruder speed, 0-255 PWM
    case 108:
      if (gc.seen & GCODE_S)
        extruder_speed = (int)gc.S;
      break;

      //custom code for debugging
    case 120:
      Serial.print("Status: (");
      Serial.print(current_units.p[X_AXIS]*100, DEC);
      Serial.print(", ");
      Serial.print(current_units.p[Y_AXIS]*100, DEC);
      Serial.print(", ");
      Serial.print(current_units.p[Z_AXIS]*100, DEC);
      Serial.print(")");

      Serial.print(" [");
      Serial.print(read_switch(X_MIN_PIN)?'1':'0');
      Serial.print(read_switch(Y_MIN_PIN)?'1':'0');
      Serial.print(read_switch(Z_MAX_PIN)?'1':'0');
      Serial.print("]");

      Serial.println();

      break;

    default:
      Serial.print("Unsupported M-Code: M");
      Serial.println(gc.M, DEC);
    }
    Serial.print("ok:");
    Serial.println(128-Serial.available(), DEC);
    return;
  }

  // Something wrong happened
  Serial.print("error: ");
  instruction[size] = '\0';
  Serial.println(instruction);
}

int scan_float(char *str, float *valp, unsigned int *seen, unsigned int flag)
{
  float res;
  int len;
  char *end;

  res = (float)strtod(str, &end);
  len = end - str;

  if (len > 0) {
    *valp = res;
    *seen |= flag;
  }
  else {
    *valp = 0;
  }

  return len;	/* length of number */
}

int scan_int(char *str, int *valp, unsigned int *seen, unsigned int flag)
{
  int res;
  int len;
  char *end;

  res = (int)strtol(str, &end, 10);
  len = end - str;

  if (len > 0) {
    *valp = res;
    *seen |= flag;
  }
  else {
    *valp = 0;
  }

  return len;	/* length of number */
}