1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
|
/*
* Pasteextruder
*
*/
#include "configuration.h"
#define SDAPin 18
int Currentstate = 3;
int Requiredstate = 0;
int Motorstate = 0;
const int ledPin = 13; // LED connected to digital pin 13
const int motorstate = 0;
const int analogthreshold = 512;
const int Selectionpin = 7;
const int Powerpin = 6;
const int Motorreverse = 20 ;
/* Definition of extruderstates
0 = Neutral / Exhaust
1 = Extruder 1 Extrude On
2 = Extruder 2 Extrude On
3 = State Unknown / Startup
Definition of Motorstates
-1 = Anticlockwisse
0 = Off
1 = Clockwise
*/
void setup() // run once, when the sketch starts
{
Serial.begin(9600);
Serial.println("Starting");
pinMode(ledPin, OUTPUT); // sets the digital pin as output
pinMode(H1D, OUTPUT);
pinMode(H1E, OUTPUT);
pinMode(H2D, OUTPUT);
pinMode(H2E, OUTPUT);
pinMode(SDAPin, INPUT);
}
int StopMotor(int Motorstate){
int result;
if (Motorstate == 1){
digitalWrite(H1D, 0);
digitalWrite(H2D, 0);
digitalWrite(H1E, HIGH);
digitalWrite(H2E, LOW);
delay(Motorreverse);
digitalWrite(H1E, LOW);
digitalWrite(H2E, LOW);
result = 0;
Serial.println("Motor Stopped from clockwise");
}
if (Motorstate == -1){
digitalWrite(H1D, 1);
digitalWrite(H2D, 1);
digitalWrite(H1E, HIGH);
digitalWrite(H2E, LOW);
delay(Motorreverse);
digitalWrite(H1E, LOW);
digitalWrite(H2E, LOW);
result = 0;
Serial.println("Motor Stopped from anticlockwise");
}
return result;
}
int StartMotor(int RequiredMotorstate){
int result;
if (RequiredMotorstate == 1){
digitalWrite(H1D, 1);
digitalWrite(H2D, 1);
digitalWrite(H1E, HIGH);
digitalWrite(H2E, LOW);
result = 1;
Serial.println("Motor started clockwise");
}
if (RequiredMotorstate == -1){
digitalWrite(H1D, 0);
digitalWrite(H2D, 0);
digitalWrite(H1E, HIGH);
digitalWrite(H2E, LOW);
result = -1;
Serial.println("Motor started anticlockwise");
}
return result;
}
void loop() // run over and over again
{
Serial.println("Current state - ");
Serial.println(Currentstate);
if (analogRead(Powerpin)<analogthreshold){ //If both optoswitches closed, Required state is 1 i.e. Extruder 1 On
Requiredstate=1;
Serial.println("Required state - Extruder 1");
}
if (analogRead(Powerpin)>analogthreshold){ //If both Power is open, direction is closed, Required state is 2 i.e. Extruder 2 On
Requiredstate=2;
Serial.println("Required state - Extruder 2");
}
if(Currentstate == 3){ // At start up, check exhaust is open, if not power the motors. When motor is required to stop, motor is reversed.
Serial.println("State unknown");
if (digitalRead(SDAPin)){
digitalWrite(ledPin, LOW); // sets the LED off
digitalWrite(H1E, LOW); //Kill Power
digitalWrite(H2E, LOW);
if (Motorstate == 1){
Motorstate = StopMotor(Motorstate);
}
Currentstate = 0;
Serial.println("Exhaust Open");
}
else{ //Turn motor clockwise until in neutral position
Motorstate = StartMotor(1);
}
}
if(Requiredstate == 0){
if(Currentstate == 0){
Serial.println("Exhaust Required - Already in Exhaust Position");
}
if(Currentstate == 1){
Serial.println("Exhaust Required - Turn Anticlockwise");
while (digitalRead(SDAPin) == 0) {
Motorstate = StartMotor(-1);
}
Motorstate = StopMotor (Motorstate);
Currentstate = 0;
}
if(Currentstate == 2){
Serial.println("Exhaust Required - Turn clockwise");
while (digitalRead(SDAPin) == 0) {
Motorstate = StartMotor(1);
}
Motorstate = StopMotor (Motorstate);
Currentstate = 0;
}
}
if(Requiredstate == 1){
if(Currentstate == 1){
Serial.println("Extruder 1 Required - Already Selected");
}
if(Currentstate != 1){
Serial.println("Extruder 1 - Turn clockwise");
while ((digitalRead(SDAPin) == 1)) {
Motorstate = StartMotor(1);
}
Motorstate = StopMotor (Motorstate);
Currentstate = 1;
}
}
if(Requiredstate == 2){
if(Currentstate == 2){
Serial.println("Extruder 2 Required - Already Selected");
}
if(Currentstate != 2){
Serial.println("Extruder 2 - Turn anticlockwise");
while ((digitalRead(SDAPin) == 1)) {
Motorstate = StartMotor(-1);
}
Motorstate = StopMotor (Motorstate);
Currentstate = 2;
}
}
}
/*
if(Currentstate == 0){
if(Requiredstate == 0){
if(Motorstate != 0){ //If motor was turning apply break
Motorstate = StopMotor(Motorstate);
}
}
if (Requiredstate == 1){
Motorstate = StartMotor(1);
}
if (Requiredstate ==-1){
Motorstate = StartMotor(-1);
}
}
if(Requiredstate == 1){
if(Currentstate == 1){
Motorstate = StopMotor(Motorstate);
}
if(Motorstate ==1){ //If motor was turning apply break
Motorstate = StopMotor(Motorstate);
Currentstate = 1
}
if(Motorstate ==-1){ //If motor was turning apply break
Motorstate = StopMotor(Motorstate);
Currentstate = 2
}
else {
Motorstate = StartMotor(-1);
}
}
if(Currentstate == 2){
if(Requiredstate == 2){
if(Motorstate != 0){ //If motor was turning apply break
Motorstate = StopMotor(Motorstate);
}
}
else {
Motorstate = StartMotor(1);
}
}
}
*/
|