1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
|
/*
*
* RepRap, The Replicating Rapid Prototyper Project
*
* http://reprap.org/
*
* RepRap is copyright (C) 2005-6 University of Bath, the RepRap
* researchers (see the project's People webpage), and other contributors.
*
* RepRap is free; you can redistribute it and/or modify it under the
* terms of the GNU Library General Public Licence as published by the
* Free Software Foundation; either version 2 of the Licence, or (at your
* option) any later version.
*
* RepRap is distributed in the hope that it will be useful, but WITHOUT
* ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
* FITNESS FOR A PARTICULAR PURPOSE. See the GNU Library General Public
* Licence for more details.
*
* For this purpose the words "software" and "library" in the GNU Library
* General Public Licence are taken to mean any and all computer programs
* computer files data results documents and other copyright information
* available from the RepRap project.
*
* You should have received a copy of the GNU Library General Public
* Licence along with RepRap (in reports, it will be one of the
* appendices, for example); if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA, or see
*
* http://www.gnu.org/
*
*/
#include "extruder.h"
#include "serial.h"
typedef unsigned int config;
config at 0x2007 __CONFIG = _CP_OFF &
_WDT_OFF &
_BODEN_OFF &
_PWRTE_ON &
_INTRC_OSC_NOCLKOUT &
_MCLRE_OFF &
_LVP_OFF;
byte deviceAddress = PORT;
static void isr() interrupt 0 {
serialInterruptHandler();
if (RBIF)
motorTick();
if (TMR1IF) {
timerTick();
TMR1IF = 0;
}
}
void init1()
{
byte v = 0;
OPTION_REG = BIN(01011111); // Disable TMR0 on RA4, 1:128 WDT, pullups on
CMCON = BIN(00000010); // Comparator: compare RA0 to int. ref.
TRISA = BIN(11111111); // Port A all inputs for now
TRISB = BIN(11000110); // Port B outputs, except 1/2 for serial and
// RB7 for optointerrupter input
// RB6 for material out detector
// RB0 for heater controller output
// Note port B3 will be used for PWM output (CCP1)
PIE1 = BIN(00000000); // All peripheral interrupts initially disabled
INTCON = BIN(00000000); // Interrupts disabled
PIR1 = 0; // Clear peripheral interrupt flags
SPBRG = 12; // 12 = ~19200 baud @ 4MHz
TXSTA = BIN(00000100); // 8 bit high speed
RCSTA = BIN(10000000); // Enable port for 8 bit receive
RCIE = 1; // Enable receive interrupts
CREN = 1; // Start reception
TXEN = 1; // Enable transmit
RBIE = 1; // Enable RB port change interrupt
PEIE = 1; // Peripheral interrupts on
GIE = 1; // Now turn on interrupts
PORTB = BIN(11000000); // Pullup on RB6,RB7 for opto-inputs
PORTA = 0;
TRISA = BIN(11000010) | PORTATRIS; // Turn off A/D lines,
// but set others as required
TMR1IE = 0;
T1CON = BIN(00000000); // Timer 1 in clock mode with 1:1 scale
TMR1IE = 1; // Enable timer interrupt
TMR1ON = 1;
PR2 = PWMPeriod; // Initial PWM period
CCP1CON = BIN(00001100); // Enable PWM mode
CCPR1L = 0; // Start turned off
T2CON = BIN(00000100); // Enable timer 2 and set prescale to 1
}
void main() {
init2(); // Order is important here, otherwise interrupts will occur
// before initialisation. Once sdcc bugs are fixed, this
// will not matter.
init1();
serial_init();
// Clear up any boot noise from the TSR
uartTransmit(0);
for(;;) {
if (packetReady()) {
processCommand();
releaseLock();
}
checkTemperature();
clearwdt();
}
}
|
