1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
|
package org.reprap;
import java.io.IOException;
import javax.media.j3d.Appearance;
import org.reprap.Device;
public interface Extruder {
/**
* Dispose of the extruder object
*/
public void dispose();
/**
* Start the extruder motor at a given speed. This ranges from 0
* to 255 but is scaled by maxSpeed and t0, so that 255 corresponds to the
* highest permitted speed. It is also scaled so that 0 would correspond
* with the lowest extrusion speed.
* @param speed The speed to drive the motor at (0-255)
* @throws IOException
*/
public void setExtrusion(int speed) throws IOException;
/**
* Start the extruder motor at a given speed. This ranges from 0
* to 255 but is scaled by maxSpeed and t0, so that 255 corresponds to the
* highest permitted speed. It is also scaled so that 0 would correspond
* with the lowest extrusion speed.
* @param speed The speed to drive the motor at (0-255)
* @param reverse If set, run extruder in reverse
* @throws IOException
*/
public void setExtrusion(int speed, boolean reverse) throws IOException;
/**
* Turn the heater of the extruder on. Inital temperatur is defined by ???
* @throws Exception
*/
public void heatOn() throws Exception;
/**
* Set the temperature of the extruder at a given height. This height is given
* in centigrades, i.e. 100 equals 100 centigrades.
* @param temperature The temperature of the extruder in centigrades
* @throws Exception
*/
public void setTemperature(double temperature) throws Exception;
/**
* Set a heat output power. For normal production use you would
* normally call setTemperature, however this method may be useful
* for lower temperature profiling, etc.
* @param heat Heater power (0-255)
* @param maxTemp Cutoff temperature in celcius
* @throws IOException
*/
public void setHeater(int heat, double maxTemp) throws IOException;
/**
* Check if the extruder is out of feedstock
* @return true if there is no material remaining
*/
public boolean isEmpty();
/**
* @return the target temperature of the extruder
*/
public double getTemperatureTarget();
/**
* @return the default temperature of the extruder
*/
public double getDefaultTemperature();
/**
* @return the current temperature of the extruder
*/
public double getTemperature();
/**
* @return the infill speed as a value between [0,1]
*/
public double getInfillSpeed();
/**
* @return the outline speed as a avlue between [0,1]
*/
public double getOutlineSpeed();
/**
* @return The length in mm to speed up when going round corners
*/
public double getAngleSpeedUpLength();
/**
* The factor by which to speed up when going round a corner.
* The formula is speed = baseSpeed*[1 - 0.5*(1 + ca)*getAngleSpeedFactor()]
* where ca is the cos of the angle between the lines. So it goes fastest when
* the line doubles back on itself (returning 1), and slowest when it
* continues straight (returning 1 - getAngleSpeedFactor()).
* @return the angle-speed factor
*/
public double getAngleSpeedFactor();
/**
* Turn the cooler (fan?) on or off
* @param f true if the cooler is to be turned on, false to turn off
* @throws IOException
*/
public void setCooler(boolean f) throws IOException ;
/**
* Check if the extruder is available, which is determined by ???
* @return true if the extruder is available
*/
public boolean isAvailable();
/**
* The speed of X and Y movement
* @return the XY speed
*/
public int getXYSpeed();
/**
* @return the extruder speeds
*/
public int getExtruderSpeed();
/**
* @return the extrusion size in millimeters
*/
public double getExtrusionSize();
/**
* @return the extrusion height in millimeters
*/
public double getExtrusionHeight();
/**
* @return the extrusion infill width in millimeters
*/
public double getExtrusionInfillWidth();
/**
* @return the extrusion overrun in millimeters
*/
public double getExtrusionOverRun();
/**
* @return the extrusion delay in seconds
*/
public long getExtrusionDelay();
/**
* @return the cooling period in seconds
*/
public int getCoolingPeriod();
/**
* @return the X offset in millimeters
*/
public double getOffsetX();
/**
* @return the Y offset in millimeters
*/
public double getOffsetY();
/**
* @return the Z offset in millimeters
*/
public double getOffsetZ();
/**
* @return the appearance (colour) to use in the simulation window for this material
*/
public Appearance getAppearance();
}
|
