blob: f07b9a84a54ead505fa87f63173feae67e19a45c (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
|
# Firmware files are in /lib/firmware/hm2/7i43/
# Must symlink the hostmot2 firmware directory of sanbox to
# /lib/firmware before running EMC2...
# sudo ln -s $HOME/emc2-sandbox/src/hal/drivers/mesa-hostmot2/firmware /lib/firmware/hm2
#
# See also:
# <http://www.linuxcnc.org/docs/devel/html/man/man9/hostmot2.9.html#config%20modparam>
# and http://wiki.linuxcnc.org/cgi-bin/emcinfo.pl?HostMot2
#
# #####################################################################
# ******************
# Core EMC/HAL Loads
# kinematics
loadrt trivkins
# motion controller, get name and thread periods from ini file
loadrt [EMCMOT]EMCMOT servo_period_nsec=[EMCMOT]SERVO_PERIOD num_joints=[TRAJ]AXES
# only the 7i43 needs this, but it doesnt hurt the others
# loadrt probe_parport
loadrt hal_parport cfg=0x378
# hostmot2 driver
loadrt hostmot2
# load low-level driver
loadrt [HOSTMOT2](DRIVER) config=[HOSTMOT2](CONFIG)
# Torch Height Control
loadrt thc
addf thc servo-thread
# THREADS
addf hm2_[HOSTMOT2](BOARD).0.read servo-thread
addf motion-command-handler servo-thread
addf motion-controller servo-thread
addf hm2_[HOSTMOT2](BOARD).0.write servo-thread
addf hm2_[HOSTMOT2](BOARD).0.pet_watchdog servo-thread
addf parport.0.read servo-thread
addf parport.0.write servo-thread
# #############################################
# Axis-of-motion Specific Configs (not the GUI)
# **********
# X [0] Axis
# axis enable chain
newsig emcmot.00.enable bit
sets emcmot.00.enable FALSE
net emcmot.00.enable <= axis.0.amp-enable-out
net emcmot.00.enable => hm2_[HOSTMOT2](BOARD).0.stepgen.00.enable
# position command and feedback
net emcmot.00.pos-cmd <= axis.0.motor-pos-cmd
net emcmot.00.pos-cmd => hm2_[HOSTMOT2](BOARD).0.stepgen.00.position-cmd
net motor.00.pos-fb <= hm2_[HOSTMOT2](BOARD).0.stepgen.00.position-fb
net motor.00.pos-fb => axis.0.motor-pos-fb
# timing parameters
setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.dirsetup [AXIS_0]DIRSETUP
setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.dirhold [AXIS_0]DIRHOLD
setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.steplen [AXIS_0]STEPLEN
setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.stepspace [AXIS_0]STEPSPACE
setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.position-scale [AXIS_0]SCALE
setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.maxvel 0
setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.maxaccel [AXIS_0]STEPGEN_MAXACCEL
setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.step_type 0
net both-home-x <= parport.0.pin-10-in-not
net both-home-x => axis.0.home-sw-in
net both-home-x => axis.0.neg-lim-sw-in
net both-home-x => axis.0.pos-lim-sw-in
# ################
# Y [1] Axis
# ################
# axis enable chain
newsig emcmot.01.enable bit
sets emcmot.01.enable FALSE
net emcmot.01.enable <= axis.1.amp-enable-out
net emcmot.01.enable => hm2_[HOSTMOT2](BOARD).0.stepgen.01.enable
# position command and feedback
net emcmot.01.pos-cmd <= axis.1.motor-pos-cmd
net emcmot.01.pos-cmd => hm2_[HOSTMOT2](BOARD).0.stepgen.01.position-cmd
net motor.01.pos-fb <= hm2_[HOSTMOT2](BOARD).0.stepgen.01.position-fb
net motor.01.pos-fb => axis.1.motor-pos-fb
# timing parameters
setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.dirsetup [AXIS_1]DIRSETUP
setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.dirhold [AXIS_1]DIRHOLD
setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.steplen [AXIS_1]STEPLEN
setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.stepspace [AXIS_1]STEPSPACE
setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.position-scale [AXIS_1]SCALE
setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.maxvel 0
setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.maxaccel [AXIS_1]STEPGEN_MAXACCEL
setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.step_type 0
net both-home-y <= parport.0.pin-11-in-not
net both-home-y => axis.1.home-sw-in
net both-home-y => axis.1.neg-lim-sw-in
net both-home-y => axis.1.pos-lim-sw-in
# ################
# Z [2] Axis
# ################
# axis enable chain
newsig emcmot.02.enable bit
sets emcmot.02.enable FALSE
net emcmot.02.enable <= axis.2.amp-enable-out
net emcmot.02.enable => hm2_[HOSTMOT2](BOARD).0.stepgen.02.enable
# position command and feedback
# hijack position command and feed through thc
net emcmot.02.pos-cmd thc.z-pos-in <= axis.2.motor-pos-cmd
net thc-pos-cmd thc.z-pos-out => hm2_[HOSTMOT2](BOARD).0.stepgen.02.position-cmd
net motor.02.pos-fb axis.2.motor-pos-fb <= thc.z-fb-out
net both-home-z => axis.2.home-sw-in
net both-home-z => axis.2.neg-lim-sw-in
net both-home-z => axis.2.pos-lim-sw-in
# timing parameters
setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.dirsetup [AXIS_2]DIRSETUP
setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.dirhold [AXIS_2]DIRHOLD
setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.steplen [AXIS_2]STEPLEN
setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.stepspace [AXIS_2]STEPSPACE
setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.position-scale [AXIS_2]SCALE
setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.maxvel 0
setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.maxaccel [AXIS_2]STEPGEN_MAXACCEL
setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.step_type 0
net both-home-z <= parport.0.pin-12-in-not
net both-home-z => axis.2.home-sw-in
net both-home-z => axis.2.neg-lim-sw-in
net both-home-z => axis.2.pos-lim-sw-in
#######################
# Standard I/O Block - EStop, Etc
# ###############################
# create a signal for the estop loopback
net estop-loop iocontrol.0.user-enable-out => iocontrol.0.emc-enable-in
# create signals for tool loading loopback
net tool-prep-loop iocontrol.0.tool-prepare => iocontrol.0.tool-prepared
net tool-change-loop iocontrol.0.tool-change => iocontrol.0.tool-changed
# Touch Off
net torch-probe motion.probe-input <= parport.0.pin-13-in-not
# Set up the Encoder for the THC
setp hm2_5i20.0.encoder.00.counter-mode 1
net thc-vel-in hm2_5i20.0.encoder.00.velocity => thc.encoder-vel
setp thc.scale-offset 119000
setp thc.vel-scale 0.00037866834
# this might need to be increased
setp thc.correction-vel 0.0001
# spindle on starts the arc
net spindle-on motion.spindle-on => parport.0.pin-16-out
net spindle-on thc.torch-on
# starts the motion when the plasma arc has transfered to the work
net start-motion-input thc.arc-ok <= motion.digital-in-00 <= parport.0.pin-15-in
# ******
# For Joypad, the rest are in postgui.hal
loadusr hal_input -W -KRAL Dual
|
