executing
    1 N..... USE_LENGTH_UNITS(CANON_UNITS_MM)
    2 N..... SET_G5X_OFFSET(1, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000)
    3 N..... SET_G92_OFFSET(0.0000, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000)
    4 N..... SET_XY_ROTATION(0.0000)
    5 N..... SET_FEED_REFERENCE(CANON_XYZ)
    6 N..... MESSAGE(" before introspect: call_level= 0.000000")
    7 N..... SELECT_POCKET(3)
    8 N..... START_CHANGE()
    9 N..... STOP_SPINDLE_TURNING()
   10 N..... CHANGE_TOOL(3)
   11 N..... SET_FEED_RATE(200.0000)
   12 N..... SET_SPINDLE_SPEED(3000.0000)
   13 N..... START_SPINDLE_CLOCKWISE()
debug:  1073741824 logging: 0
call_level= 1
argc= 4
args=( 1.00000 2.00000 3.00000 3.14159 )
param # 0 = 1.0
param # 1 = 2.0
param # 2 = 3.0
param # 3 = 3.14159
current oword subname= introspect
m_modes[0]= -1
g_modes[0]= -1
current tool= 3.0 3.0
feed= 200.0
speed= 3000.0
global parameter set in test.ngc: 47.11
parameter set via test.ini: 3.14159
locals:  ['a_new_local']
globals:  ['_a', '_a_global_set_in_test_dot_ngc', '_a_new_global', '_absolute', '_adaptive_feed', '_b', '_c', '_call_level', '_ccomp', '_coord_system', '_current_pocket', '_current_tool', '_feed', '_feed_hold', '_feed_override', '_flood', '_ijk_absolute_mode', '_imperial', '_incremental', '_ini[example]variable', '_inverse_time', '_lathe_diameter_mode', '_lathe_radius_mode', '_line', '_metric', '_mist', '_motion_mode', '_plane', '_remap_level', '_retract_old_z', '_retract_r_plane', '_rpm', '_selected_pocket', '_selected_tool', '_speed_override', '_spindle_css_mode', '_spindle_cw', '_spindle_on', '_spindle_rpm_mode', '_task', '_tool_offset', '_u', '_units_per_minute', '_units_per_rev', '_v', '_value', '_value_returned', '_vmajor', '_vminor', '_w', '_x', '_y', '_z', 'foo']
params():  ['a_new_local', '_a', '_a_global_set_in_test_dot_ngc', '_a_new_global', '_absolute', '_adaptive_feed', '_b', '_c', '_call_level', '_ccomp', '_coord_system', '_current_pocket', '_current_tool', '_feed', '_feed_hold', '_feed_override', '_flood', '_ijk_absolute_mode', '_imperial', '_incremental', '_ini[example]variable', '_inverse_time', '_lathe_diameter_mode', '_lathe_radius_mode', '_line', '_metric', '_mist', '_motion_mode', '_plane', '_remap_level', '_retract_old_z', '_retract_r_plane', '_rpm', '_selected_pocket', '_selected_tool', '_speed_override', '_spindle_css_mode', '_spindle_cw', '_spindle_on', '_spindle_rpm_mode', '_task', '_tool_offset', '_u', '_units_per_minute', '_units_per_rev', '_v', '_value', '_value_returned', '_vmajor', '_vminor', '_w', '_x', '_y', '_z', 'foo']
   14 N..... MESSAGE(" after introspect: return value=2.718280 call_level= 0.000000")
   15 N..... SET_G5X_OFFSET(1, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000)
   16 N..... SET_XY_ROTATION(0.0000)
   17 N..... SET_FEED_MODE(0)
   18 N..... SET_FEED_RATE(0.0000)
   19 N..... STOP_SPINDLE_TURNING()
   20 N..... SET_SPINDLE_MODE(0.0000)
   21 N..... PROGRAM_END()