N..... USE_LENGTH_UNITS(CANON_UNITS_MM)
 N..... SET_ORIGIN_OFFSETS(0.0000, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... SET_FEED_REFERENCE(CANON_XYZ)
 N..... SET_FEED_RATE(30.0000)
 N..... SELECT_PLANE(CANON_PLANE_XZ)
 N..... USE_LENGTH_UNITS(CANON_UNITS_INCHES)
 N..... USE_TOOL_LENGTH_OFFSET(0.0000 0.0000)
 N..... SELECT_TOOL(0)
 N..... STOP_SPINDLE_TURNING()
 N..... CHANGE_TOOL(0)
 N..... STRAIGHT_TRAVERSE(0.3000, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... COMMENT("interpreter: cutter radius compensation off")
 N..... STRAIGHT_FEED(0.1000, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... ARC_FEED(0.1000, 0.0000, 0.1000, 0.1000, 1, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... STRAIGHT_FEED(0.0000, 0.0000, 1.0000, 0.0000, 0.0000, 0.0000)
 N..... ARC_FEED(1.2500, -0.2500, 1.0000, -0.2500, -1, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... ARC_FEED(1.5000, -0.5000, 1.5000, -0.2500, 1, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... STRAIGHT_FEED(-0.5000, 0.0000, 1.7500, 0.0000, 0.0000, 0.0000)
 N..... STRAIGHT_TRAVERSE(0.3000, 0.0000, 1.7500, 0.0000, 0.0000, 0.0000)
 N..... SELECT_TOOL(2)
 N..... STOP_SPINDLE_TURNING()
 N..... CHANGE_TOOL(2)
 N..... USE_TOOL_LENGTH_OFFSET(0.0000 0.0000)
 N..... STRAIGHT_TRAVERSE(0.3000, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... COMMENT("interpreter: cutter radius compensation on right")
 N..... STRAIGHT_FEED(0.0500, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... ARC_FEED(0.0500, 0.0000, 0.0500, 0.0500, 1, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... STRAIGHT_FEED(0.0000, 0.0000, 0.9500, 0.0000, 0.0000, 0.0000)
 N..... ARC_FEED(1.2500, -0.3000, 0.9500, -0.3000, -1, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... ARC_FEED(1.4500, -0.5000, 1.4500, -0.3000, 1, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... STRAIGHT_FEED(-0.5000, 0.0000, 1.7000, 0.0000, 0.0000, 0.0000)
 N..... COMMENT("interpreter: cutter radius compensation off")
 N..... STRAIGHT_TRAVERSE(0.3000, 0.0000, 1.7500, 0.0000, 0.0000, 0.0000)
 N..... SELECT_TOOL(7)
 N..... STOP_SPINDLE_TURNING()
 N..... CHANGE_TOOL(7)
 N..... USE_TOOL_LENGTH_OFFSET(0.0000 0.0000)
 N..... STRAIGHT_TRAVERSE(0.3000, 0.0000, 1.8500, 0.0000, 0.0000, 0.0000)
 N..... STRAIGHT_TRAVERSE(-0.3000, 0.0000, 1.8500, 0.0000, 0.0000, 0.0000)
 N..... COMMENT("interpreter: cutter radius compensation on left")
 N..... STRAIGHT_FEED(-0.3600, 0.0000, 1.7700, 0.0000, 0.0000, 0.0000)
 N..... ARC_FEED(1.7500, -0.4000, 1.8000, -0.4000, 1, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... ARC_FEED(1.7000, -0.4500, 1.7000, -0.4000, -1, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... STRAIGHT_FEED(-0.4500, 0.0000, 1.4500, 0.0000, 0.0000, 0.0000)
 N..... ARC_FEED(1.2500, -0.2500, 1.4500, -0.2500, -1, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... ARC_FEED(0.9500, 0.0500, 0.9500, -0.2500, 1, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... STRAIGHT_FEED(0.0500, 0.0000, 0.0500, 0.0000, 0.0000, 0.0000)
 N..... ARC_FEED(0.0000, 0.1000, 0.0500, 0.1000, -1, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... COMMENT("interpreter: cutter radius compensation off")
 N..... STRAIGHT_TRAVERSE(0.3000, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... USE_TOOL_LENGTH_OFFSET(0.0000 0.0000)
 N..... SELECT_TOOL(0)
 N..... STOP_SPINDLE_TURNING()
 N..... CHANGE_TOOL(0)
 N..... SET_ORIGIN_OFFSETS(0.0000, 0.0000, 0.0000, 0.0000, 0.0000, 0.0000)
 N..... SELECT_PLANE(CANON_PLANE_XY)
 N..... STOP_SPINDLE_TURNING()
 N..... PROGRAM_END()