# #######################################
#
# HAL file for HostMot2 with 3 steppers
#
# Derived from Ted Hyde's original hm2-servo config
#
# Based up work and discussion with Seb & Peter & Jeff
# GNU license references - insert here. www.linuxcnc.org
#
#
# ########################################
# Firmware files are in /lib/firmware/hm2/7i43/
# Must symlink the hostmot2 firmware directory of sanbox to
# /lib/firmware before running EMC2...
# sudo ln -s $HOME/emc2-sandbox/src/hal/drivers/mesa-hostmot2/firmware /lib/firmware/hm2
#
# See also:
# <http://www.linuxcnc.org/docs/devel/html/man/man9/hostmot2.9.html#config%20modparam>
# and http://wiki.linuxcnc.org/cgi-bin/emcinfo.pl?HostMot2
#
# #####################################################################


# ###################################
# Core EMC/HAL Loads
# ###################################

# kinematics
loadrt trivkins

# motion controller, get name and thread periods from ini file
loadrt [EMCMOT]EMCMOT servo_period_nsec=[EMCMOT]SERVO_PERIOD num_joints=[TRAJ]AXES

# only the 7i43 needs this, but it doesnt hurt the others
loadrt probe_parport

# hostmot2 driver
loadrt hostmot2

# load low-level driver
loadrt [HOSTMOT2](DRIVER) config=[HOSTMOT2](CONFIG)


# ################################################
# THREADS
# ################################################

addf hm2_[HOSTMOT2](BOARD).0.read         servo-thread
addf motion-command-handler               servo-thread
addf motion-controller                    servo-thread
# revel in the free time here from not having to run PID 
addf hm2_[HOSTMOT2](BOARD).0.write        servo-thread
addf hm2_[HOSTMOT2](BOARD).0.pet_watchdog servo-thread
       

# ######################################################
# Axis-of-motion Specific Configs (not the GUI)
# ######################################################


# ################
# X [0] Axis
# ################

# axis enable chain
newsig emcmot.00.enable bit
sets emcmot.00.enable FALSE

net emcmot.00.enable <= axis.0.amp-enable-out 
net emcmot.00.enable => hm2_[HOSTMOT2](BOARD).0.stepgen.00.enable


# position command and feedback
net emcmot.00.pos-cmd <= axis.0.motor-pos-cmd
net emcmot.00.pos-cmd => hm2_[HOSTMOT2](BOARD).0.stepgen.00.position-cmd

net motor.00.pos-fb <= hm2_[HOSTMOT2](BOARD).0.stepgen.00.position-fb
net motor.00.pos-fb => axis.0.motor-pos-fb


# timing parameters
setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.dirsetup        [AXIS_0]DIRSETUP
setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.dirhold         [AXIS_0]DIRHOLD

setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.steplen         [AXIS_0]STEPLEN
setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.stepspace       [AXIS_0]STEPSPACE

setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.position-scale  [AXIS_0]SCALE

setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.maxvel          [AXIS_0]STEPGEN_MAX_VEL
setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.maxaccel        [AXIS_0]STEPGEN_MAX_ACC

setp hm2_[HOSTMOT2](BOARD).0.stepgen.00.step_type       0


# ################
# Y [1] Axis
# ################

# axis enable chain
newsig emcmot.01.enable bit
sets emcmot.01.enable FALSE

net emcmot.01.enable <= axis.1.amp-enable-out 
net emcmot.01.enable => hm2_[HOSTMOT2](BOARD).0.stepgen.01.enable


# position command and feedback
net emcmot.01.pos-cmd <= axis.1.motor-pos-cmd
net emcmot.01.pos-cmd => hm2_[HOSTMOT2](BOARD).0.stepgen.01.position-cmd

net motor.01.pos-fb <= hm2_[HOSTMOT2](BOARD).0.stepgen.01.position-fb
net motor.01.pos-fb => axis.1.motor-pos-fb


# timing parameters
setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.dirsetup        [AXIS_1]DIRSETUP
setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.dirhold         [AXIS_1]DIRHOLD

setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.steplen         [AXIS_1]STEPLEN
setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.stepspace       [AXIS_1]STEPSPACE

setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.position-scale  [AXIS_1]SCALE

setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.maxvel          [AXIS_1]STEPGEN_MAX_VEL
setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.maxaccel        [AXIS_1]STEPGEN_MAX_ACC

setp hm2_[HOSTMOT2](BOARD).0.stepgen.01.step_type       0


# ################
# Z [2] Axis
# ################

# axis enable chain
newsig emcmot.02.enable bit
sets emcmot.02.enable FALSE

net emcmot.02.enable <= axis.2.amp-enable-out 
net emcmot.02.enable => hm2_[HOSTMOT2](BOARD).0.stepgen.02.enable


# position command and feedback
net emcmot.02.pos-cmd <= axis.2.motor-pos-cmd
net emcmot.02.pos-cmd => hm2_[HOSTMOT2](BOARD).0.stepgen.02.position-cmd

net motor.02.pos-fb <= hm2_[HOSTMOT2](BOARD).0.stepgen.02.position-fb
net motor.02.pos-fb => axis.2.motor-pos-fb


# timing parameters
setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.dirsetup        [AXIS_2]DIRSETUP
setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.dirhold         [AXIS_2]DIRHOLD

setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.steplen         [AXIS_2]STEPLEN
setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.stepspace       [AXIS_2]STEPSPACE

setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.position-scale  [AXIS_2]SCALE

setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.maxvel          [AXIS_2]STEPGEN_MAX_VEL
setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.maxaccel        [AXIS_2]STEPGEN_MAX_ACC

setp hm2_[HOSTMOT2](BOARD).0.stepgen.02.step_type       0




# 
# The Mesa AnyIO output pins can be in open-drain mode (drive low, float
# high) or push/pull mode (drive low, drive high).
#
# When a logical output is 1 in open-drain mode, the FPGA lets the pin
# float and it gets pulled high to +5V via a 10K resistor.
#
# When a logical output is 1 in push/pull mode, the FPGA pushes the pin
# high but only to +3.3V.  This is problematic on some kinds of inputs.
#

#setp hm2_[HOSTMOT2](BOARD).0.gpio.048.is_opendrain 1
#setp hm2_[HOSTMOT2](BOARD).0.gpio.049.is_opendrain 1

#setp hm2_[HOSTMOT2](BOARD).0.gpio.054.is_opendrain 1
#setp hm2_[HOSTMOT2](BOARD).0.gpio.055.is_opendrain 1

#setp hm2_[HOSTMOT2](BOARD).0.gpio.060.is_opendrain 1
#setp hm2_[HOSTMOT2](BOARD).0.gpio.061.is_opendrain 1




# ##################################################
# Standard I/O Block - EStop, Etc
# ##################################################

# create a signal for the estop loopback
net estop-loop iocontrol.0.user-enable-out => iocontrol.0.emc-enable-in

# create signals for tool loading loopback
net tool-prep-loop iocontrol.0.tool-prepare => iocontrol.0.tool-prepared
net tool-change-loop iocontrol.0.tool-change => iocontrol.0.tool-changed