loadrt trivkins
loadrt [EMCMOT]EMCMOT base_period_nsec=[EMCMOT]BASE_PERIOD servo_period_nsec=[EMCMOT]SERVO_PERIOD num_joints=[TRAJ]AXES
loadrt probe_parport
loadrt hal_parport cfg=0x378
setp parport.0.reset-time 4000
loadrt stepgen step_type=0,0,0,0,0 ctrl_type=p,p,p,p,v

loadrt estop_latch
net charge-pump <= estop-latch.0.watchdog

addf parport.0.read base-thread
addf stepgen.make-pulses base-thread
addf estop-latch.0 base-thread
addf parport.0.write base-thread
addf parport.0.reset base-thread

addf stepgen.capture-position servo-thread
addf motion-command-handler servo-thread
addf motion-controller servo-thread
addf stepgen.update-freq servo-thread
net spindle-cw <= motion.spindle-forward
net coolant-flood <= iocontrol.0.coolant-flood
net spindle-on motion.spindle-on stepgen.4.enable


#
# Spindle gear selection code.
#
# emc2 (rpm) => gearchange => stepgen (step & dir) => spindle
# low gear:  100-2000 rpm, 327 ppr, 10900 Hz => 2000 rpm, 5.450 Hz/rpm
# high gear: 250-5140 rpm, 127 ppr, 10900 Hz => 5140 rpm, 2.121 Hz/rpm
# low/high ppr = 327/127 = 2.575
#

setp stepgen.4.maxaccel 20000
setp stepgen.4.maxvel 2000
setp stepgen.4.position-scale 5.450
net spindle-pwm stepgen.4.step parport.0.pin-01-out
setp stepgen.4.stepspace 0
setp stepgen.4.steplen 1
setp parport.0.pin-01-out-reset 1
loadrt or2 count=1
net spindle-cw or2.0.in0
net spindle-ccw motion.spindle-reverse or2.0.in1

loadrt toggle count=1
loadrt not count=1
loadrt gearchange count=1
addf toggle.0 servo-thread
addf not.0 servo-thread
addf gearchange.0 servo-thread
setp toggle.0.debounce 0
setp gearchange.0.min1 100
setp gearchange.0.max1 2000
setp gearchange.0.min2 250
setp gearchange.0.max2 5140
setp gearchange.0.scale2 2.575
# we're not controlling the direction with the gearchanger, so reverse isn't set
# and the dir-in and dir-out pins aren't linked
net spindle-speed-raw motion.spindle-speed-out gearchange.0.speed-in
net spindle-speed gearchange.0.speed-out stepgen.4.velocity-cmd

net xdir => parport.0.pin-02-out
setp parport.0.pin-03-out-invert 1
net xstep => parport.0.pin-03-out
setp parport.0.pin-03-out-reset 1
net ydir => parport.0.pin-04-out
setp parport.0.pin-05-out-invert 1
net ystep => parport.0.pin-05-out
setp parport.0.pin-05-out-reset 1
setp parport.0.pin-06-out-invert 1
net zdir => parport.0.pin-06-out
setp parport.0.pin-07-out-invert 1
net zstep => parport.0.pin-07-out
setp parport.0.pin-07-out-reset 1
net adir => parport.0.pin-08-out
setp parport.0.pin-09-out-invert 1
net astep => parport.0.pin-09-out
setp parport.0.pin-09-out-reset 1
net coolant-flood => parport.0.pin-14-out
net spindle-cw => parport.0.pin-16-out
net charge-pump => parport.0.pin-17-out

net both-home-x <= parport.0.pin-10-in
net both-home-y <= parport.0.pin-11-in
net both-home-z <= parport.0.pin-12-in
net home-a <= parport.0.pin-13-in
net machine-ok <= parport.0.pin-15-in-not

setp stepgen.0.position-scale [AXIS_0]SCALE
setp stepgen.0.steplen 1
setp stepgen.0.stepspace 0
setp stepgen.0.dirhold 45000
setp stepgen.0.dirsetup 26000
setp stepgen.0.maxaccel [AXIS_0]STEPGEN_MAXACCEL
net xpos-cmd axis.0.motor-pos-cmd => stepgen.0.position-cmd
net xpos-fb stepgen.0.position-fb => axis.0.motor-pos-fb
net xstep <= stepgen.0.step
net xdir <= stepgen.0.dir
net xenable axis.0.amp-enable-out => stepgen.0.enable
net both-home-x => axis.0.home-sw-in
net both-home-x => axis.0.neg-lim-sw-in
net both-home-x => axis.0.pos-lim-sw-in

setp stepgen.1.position-scale [AXIS_1]SCALE
setp stepgen.1.steplen 1
setp stepgen.1.stepspace 0
setp stepgen.1.dirhold 45000
setp stepgen.1.dirsetup 26000
setp stepgen.1.maxaccel [AXIS_1]STEPGEN_MAXACCEL
net ypos-cmd axis.1.motor-pos-cmd => stepgen.1.position-cmd
net ypos-fb stepgen.1.position-fb => axis.1.motor-pos-fb
net ystep <= stepgen.1.step
net ydir <= stepgen.1.dir
net yenable axis.1.amp-enable-out => stepgen.1.enable
net both-home-y => axis.1.home-sw-in
net both-home-y => axis.1.neg-lim-sw-in
net both-home-y => axis.1.pos-lim-sw-in

setp stepgen.2.position-scale [AXIS_2]SCALE
setp stepgen.2.steplen 1
setp stepgen.2.stepspace 0
setp stepgen.2.dirhold 45000
setp stepgen.2.dirsetup 26000
setp stepgen.2.maxaccel [AXIS_2]STEPGEN_MAXACCEL
net zpos-cmd axis.2.motor-pos-cmd => stepgen.2.position-cmd
net zpos-fb stepgen.2.position-fb => axis.2.motor-pos-fb
net zstep <= stepgen.2.step
net zdir <= stepgen.2.dir
net zenable axis.2.amp-enable-out => stepgen.2.enable
net both-home-z => axis.2.home-sw-in
net both-home-z => axis.2.neg-lim-sw-in
net both-home-z => axis.2.pos-lim-sw-in

setp stepgen.3.position-scale [AXIS_3]SCALE
setp stepgen.3.steplen 1
setp stepgen.3.stepspace 0
setp stepgen.3.dirhold 45000
setp stepgen.3.dirsetup 26000
setp stepgen.3.maxaccel [AXIS_3]STEPGEN_MAXACCEL
net apos-cmd axis.3.motor-pos-cmd => stepgen.3.position-cmd
net apos-fb stepgen.3.position-fb => axis.3.motor-pos-fb
net astep <= stepgen.3.step
net adir <= stepgen.3.dir
net aenable axis.3.amp-enable-out => stepgen.3.enable
net home-a => axis.3.home-sw-in

#linksp xenable estop-latch.0.ok-out
net estop-out <= iocontrol.0.user-enable-out
net machine-ok => estop-latch.0.ok-in
net estop estop-latch.0.ok-out => iocontrol.0.emc-enable-in
net estop-reset iocontrol.0.user-request-enable => estop-latch.0.reset

loadusr -W hal_manualtoolchange
net tool-change iocontrol.0.tool-change => hal_manualtoolchange.change
net tool-changed iocontrol.0.tool-changed <= hal_manualtoolchange.changed
net tool-number iocontrol.0.tool-prep-number => hal_manualtoolchange.number
net tool-prepare-loopback iocontrol.0.tool-prepare => iocontrol.0.tool-prepared

net probe parport.0.pin-13-in-not => motion.probe-input