# HAL config file for ServoToGo STG ISA board
#
# install driver (only needed if stg_motion.hal doesn't get run)
#loadrt hal_stg

# add I/O to servo thread so they will be evaluated
# every servo period
# read inputs first
addf stg.di-read servo-thread 1
# write outputs last
addf stg.do-write servo-thread 1

#uncomment following line if ADC's are needed (for example spindle-tach feedback)
#addf stg.0.read-adcs servo-thread 1

#
# Connect motion controller I/Os
#

# connect limit/home switch outputs to motion controller
net Xminlim <= stg.in-02
net Xminlim => axis.0.neg-lim-sw-in
net Xmaxlim <= stg.in-01
net Xmaxlim => axis.0.pos-lim-sw-in
net Xhome <= stg.in-00
net Xhome => axis.0.home-sw-in

net Yminlim <= stg.in-06
net Yminlim => axis.1.neg-lim-sw-in
net Ymaxlim <= stg.in-05
net Ymaxlim => axis.1.pos-lim-sw-in
net Yhome <= stg.in-04
net Yhome => axis.1.home-sw-in

net Zminlim <= stg.in-10
net Zminlim => axis.2.neg-lim-sw-in
net Zmaxlim <= stg.in-09
net Zmaxlim => axis.2.pos-lim-sw-in
net Zhome <= stg.in-08
net Zhome => axis.2.home-sw-in

#continue in the same manner for further axes (A,B,C)

# connect amp faults to motion controller
net Xfault <= stg.in-03
net Xfault => axis.0.amp-fault-in
net Yfault <= stg.in-07
net Yfault => axis.1.amp-fault-in
net Zfault <= stg.in-11
net Zfault => axis.2.amp-fault-in

# connect index pulses to motion controller
# do these when index pulsing is figured out
#newsig Xindex bit
#newsig Yindex  bit
#newsig Zindex bit
#linksp Xindex <= stg.0.enc-index
#linksp Xindex => axis.0.index-enable
#linksp Yindex <= stg.1.enc-index
#linksp Yindex => axis.1.index-enable
#linksp Zindex <= stg.2.enc-index
#linksp Zindex => axis.2.index-enable

# connect amp enables to motion controller
net Xenable => stg.out-00
net Yenable => stg.out-01
net Zenable => stg.out-02

# connect watchdog reset to motion controller
# needs watchdo
#newsig WatchdogRst bit
#linksp WatchdogRst <= stg.watchdog-reset
#linksp WatchdogRst => motion.watchdog-reset-out


#
# Connect I/O controller I/Os
#

# connect e-stop write/sense to I/O controller
# these connections assume an external ESTOP circuitry will be used
# if it's not used, comment the next lines and uncomment the loopback
net EstopSense <= stg.in-12
net EstopSense => iocontrol.0.emc-enable-in
net EstopWrite <= stg.out-07
net EstopWrite => iocontrol.0.user-enable-out

# ESTOP loopback, only use this for a simple machine without external ESTOP
# you really SHOULDN'T use a servo machine without proper ESTOP
#net estop-loop iocontrol.0.user-enable-out iocontrol.0.emc-enable-in

# connect spindle fwd/rev to I/O controller
net SpindleFwd <= stg.out-06
net SpindleFwd => motion.spindle-forward
net SpindleRev <= stg.out-05
net SpindleRev => motion.spindle-reverse

# connect spindle brake to I/O controller
net SpindleBrakeOn <= stg.out-10
net SpindleBrakeOn => motion.spindle-brake

# connect mist/flood coolant to I/O controller
net MistOn <= stg.out-11
net MistOn => iocontrol.0.coolant-mist
net FloodOn <= stg.out-12
net FloodOn => iocontrol.0.coolant-flood

# connect lube motor run to I/O controller
net LubeOn <= stg.out-13
net LubeOn => iocontrol.0.lube

# connect lube level to I/O controller
net LubeLevel <= stg.in-13
net LubeLevel => iocontrol.0.lube_level

# create signals for tool loading loopback
net tool-prep-loop iocontrol.0.tool-prepare iocontrol.0.tool-prepared
net tool-change-loop iocontrol.0.tool-change iocontrol.0.tool-changed