# HAL config file for using classic ladder
# Loads the core_stepper.hal file first to set up motion and stepgen
# This adds limits and home from limit to the motion module
# adds the possibility of an external momentary or sustained NC estop button 
# includes intermittent lube pump and pressure or level sensing.
# includes coolant and spindle forward, reverse

# from standard pinout config file for 3-axis steppers
# using a parport for I/O

# load the parport driver
loadrt hal_parport cfg="0x378"
# next connect the parport functions to threads
addf parport.0.read base-thread 1
addf parport.0.write base-thread -1

# This configuration uses classicladder for machine logic
# (load the realtime portion)
# these classicladder parameters need to be optimized after ladder completion
loadrt classicladder_rt numRungs=12 numBits=20 numWords=4 numTimers=5 numMonostables=2 numPhysInputs=10 numPhysOutputs=10 numArithmExpr=4 numSections=4
# We kick ladder into a thread at the slower servo rate rather than base rate
addf classicladder.0.refresh        servo-thread 1

# invoke the user part of CL to silently load the program
# later we will need to add the clp file mentioned below
# to the ini file so that we do not need to hardcode it here.
loadusr -w classicladder --nogui demo_step_cl.clp
# load the GUI aswell
loadusr classicladder

# begin to connect physical pins to signals
# this is EMC's standard motion pinouts
net Xstep parport.0.pin-03-out
net Xdir parport.0.pin-02-out
net Ystep parport.0.pin-05-out
net Ydir parport.0.pin-04-out
net Zstep parport.0.pin-07-out
net Zdir parport.0.pin-06-out

# three axis motion allows 6 other outputs on pins 8,9,1,14,16,17
# five additional input pins are available 10,11,12,13,15
# these are setup by the work they perform below

# estop signals
# signal is the internal or gui estop command from EMC
net user-enable-out iocontrol.0.user-enable-out classicladder.0.in-00
# one-shot on  timer when signal above goes high.
net user-request-enable iocontrol.0.user-request-enable  classicladder.0.in-02
# this bit is an external estop button connected to parport pin 11 and ground
net ext-estop parport.0.pin-10-in
net ext-estop classicladder.0.in-01
# This bit signal is comand to estop from CL to EMC
net emc-enable-in iocontrol.0.emc-enable-in classicladder.0.out-00 

# lube signals
# lube run command from emc to CL 
net lube iocontrol.0.lube classicladder.0.in-03
# for ease of reading we will make a new signal lube-run
net lube-run classicladder.0.out-01
net lube-run parport.0.pin-01-out

# The lube sense stuff runs from an external pin, through CL to iocontrol in 
# lube-up is the signal between the parport and cl
net lube-up parport.0.pin-12-in
net lube-up classicladder.0.in-04
net lube-level iocontrol.0.lube_level classicladder.0.out-02

# coolant signals
# note that these do NOT represent proper IO signals from iocontrol
# should separate command and status for production versions
# and run these through CL to test conditions
net flood iocontrol.0.coolant-flood  parport.0.pin-08-out 
net mist  iocontrol.0.coolant-mist  parport.0.pin-09-out 

# spindle signals
# spindle status has not been resolved
# a simple loop through is set here
net spindle-forward motion.spindle-forward  parport.0.pin-16-out 
net spindle-reverse motion.spindle-reverse  parport.0.pin-17-out 

# we will let loopbacks handle tool prepare and change commands 
# though we could  index an external changer
# create connections for tool loading loopback
net tool-prep-loop iocontrol.0.tool-prepare iocontrol.0.tool-prepared
net tool-change-loop iocontrol.0.tool-change iocontrol.0.tool-changed

# create a limit switch signal
# read limit conditions from external normally open switches in parallel
# this configuration allows the control to run but still test limit 
# for real use a normally closed series loop and reverse parport pin polarity
# add all limits to a single parport pin
# connect this signal to pin 10 on the parport
net limit-reached parport.0.pin-10-in-not
# connect this signal to all limit signals of relevant axes
net limit-reached axis.0.neg-lim-sw-in
net limit-reached axis.0.pos-lim-sw-in
net limit-reached axis.1.neg-lim-sw-in
net limit-reached axis.1.pos-lim-sw-in
net limit-reached axis.2.neg-lim-sw-in
#linksp limit-reached  axis.2.pos-lim-sw-in